Ceci est une ancienne révision du document !
Table des matières
Zone Administration
Solaris Containers
The term Solaris Containers is often confused with that of Solaris Zones. In fact, there is a slight difference. The definition of a container is:
Solaris container = Solaris Zone + Solaris Resource Manager ( SRM )
The SRM is responsible for workload and resource management.
Solaris Zones are not full guest operating system kernels and as such they are similar in concept to FreeBSD Jails. Zones share the same kernel and as such cannot be live migrated to another host.
There are two types of zones:
- a single Global zone,
- one or more Non-global or local zones.
Each local zone requires about 400 Mb of disk space and 15 Mb of RAM.
The Global Zone
The global zone:
- has a zone ID of 0,
- provides a unique instance of the Solaris kernel,
- contains all packages installed by IPS,
- can contains other software not installed by IPS,
- contains a database of all applications installed in the global zone,
- contains all configuration data concerning the global zone such as its host name,
- knows about all devices and all file systems,
- is aware of all local zones as well as their configuration,
- is the zone in which local zones can be created, installed, configured, managed, un-installed and deleted.
Non-global or Local Zones
A local zone:
- is given a zone ID when it is booted,
- shares the kernel with the global zone,
- contains a some of the installed packages,
- shares packages with the global zone,
- can contain other software and files not present in the global zone,
- contains a database of all locally installed applications as well as all applications shared by the global zone,
- has no knowledge of the other local zones,
- cannot be used to manage or to un-install local zones, including itself,
- contains all configuration data concerning the local zone such as its host name and IP address,
For those familiar with Solaris 10 zones, there were two types of local zones:
- Small zones or Sparse Root zones where the zone shared the following global zone directories:
- /usr
- /lib
- /platform
- /sbin
- Big zones or Whole Root zones that contained a complete Solaris installation.
In Solaris 11 only Whole Root Zones remain.
Lab #1 - Installing a Non-global Zone
In this lab you will be installing a Local Zone into a ZFS file system. Start by looking at where you can create the directory that will contain future zones:
root@solaris:~# zfs list NAME USED AVAIL REFER MOUNTPOINT mypool 103M 51.5M 31K /mypool mypool/iscsi 103M 155M 16K - rpool 7.40G 11.9G 4.58M /rpool rpool/ROOT 5.22G 11.9G 31K legacy rpool/ROOT/solaris 5.22G 11.9G 4.08G / rpool/ROOT/solaris-backup-1 2.47M 11.9G 1.98G / rpool/ROOT/solaris-backup-1/var 46K 11.9G 758M /var rpool/ROOT/solaris-backup-2 127K 11.9G 3.92G / rpool/ROOT/solaris-backup-2/var 58K 11.9G 266M /var rpool/ROOT/solaris/var 980M 11.9G 209M /var rpool/VARSHARE 102K 11.9G 102K /var/share rpool/dump 1.03G 12.0G 1.00G - rpool/export 110M 11.9G 32K /export rpool/export/home 110M 11.9G 32K /export/home rpool/export/home/trainee 110M 11.9G 110M /export/home/trainee rpool/swap 1.03G 12.0G 1.00G -
You cannot create zone datasets under the rpool/ROOT dataset.
Configuring the Zone's Dataset
It seems that the best option is to create a new file system just for zones:
root@solaris:~# zfs create -o mountpoint=/zones rpool/zones root@solaris:~# zfs list NAME USED AVAIL REFER MOUNTPOINT mypool 103M 51.5M 31K /mypool mypool/iscsi 103M 155M 16K - rpool 7.40G 11.9G 4.58M /rpool rpool/ROOT 5.22G 11.9G 31K legacy rpool/ROOT/solaris 5.22G 11.9G 4.08G / rpool/ROOT/solaris-backup-1 2.47M 11.9G 1.98G / rpool/ROOT/solaris-backup-1/var 46K 11.9G 758M /var rpool/ROOT/solaris-backup-2 127K 11.9G 3.92G / rpool/ROOT/solaris-backup-2/var 58K 11.9G 266M /var rpool/ROOT/solaris/var 980M 11.9G 209M /var rpool/VARSHARE 102K 11.9G 102K /var/share rpool/dump 1.03G 12.0G 1.00G - rpool/export 110M 11.9G 32K /export rpool/export/home 110M 11.9G 32K /export/home rpool/export/home/trainee 110M 11.9G 110M /export/home/trainee rpool/swap 1.03G 12.0G 1.00G - rpool/zones 31K 11.9G 31K /zones
Now create your zone using the zonecfg command:
root@solaris:~# zonecfg -z myzone Use 'create' to begin configuring a new zone. zonecfg:myzone> create create: Using system default template 'SYSdefault' zonecfg:myzone> set zonepath=/zones/myzone zonecfg:myzone> set autoboot=true zonecfg:myzone>
The -z switch stands for the zonename.
Zones are represented by XML files. As you can see above, when created, the zonecfg uses the default template /etc/zones/SYSdefault.xml:
root@solaris:~# cat /etc/zones/SYSdefault.xml
<?xml version="1.0"?>
<!--
Copyright (c) 2010, 2011, Oracle and/or its affiliates. All rights reserved.
DO NOT EDIT THIS FILE. Use zonecfg(1M) instead.
-->
<!DOCTYPE zone PUBLIC "-//Sun Microsystems Inc//DTD Zones//EN" "file:///usr/share/lib/xml/dtd/zonecfg.dtd.1">
<zone name="default" zonepath="" autoboot="false" brand="solaris"
ip-type="exclusive">
<automatic-network lower-link="auto" linkname="net0"
link-protection="mac-nospoof" mac-address="random"/>
</zone>
Note that you also have set the autoboot property to yes so that the zone starts on system boot.
To show the configuration that zonecfg has already filled in for you by using the /etc/zones/SYSdefault.xml file, use the command info :
zonecfg:myzone> info zonename: myzone zonepath: /zones/myzone brand: solaris autoboot: true bootargs: file-mac-profile: pool: limitpriv: scheduling-class: ip-type: exclusive hostid: fs-allowed: anet: linkname: net0 lower-link: auto allowed-address not specified configure-allowed-address: true defrouter not specified allowed-dhcp-cids not specified link-protection: mac-nospoof mac-address: random mac-prefix not specified mac-slot not specified vlan-id not specified priority not specified rxrings not specified txrings not specified mtu not specified maxbw not specified rxfanout not specified vsi-typeid not specified vsi-vers not specified vsi-mgrid not specified etsbw-lcl not specified cos not specified pkey not specified linkmode not specified zonecfg:myzone>
Finally, commit the configuration, verify the newly created XML file and quit:
zonecfg:myzone> commit zonecfg:myzone> verify zonecfg:myzone> exit root@solaris:~#
Your zone's configuration is now in its own XML file:
root@solaris:~# cat /etc/zones/myzone.xml
<?xml version="1.0" encoding="UTF-8"?>
<!DOCTYPE zone PUBLIC "-//Sun Microsystems Inc//DTD Zones//EN" "file:///usr/share/lib/xml/dtd/zonecfg.dtd.1">
<!--
DO NOT EDIT THIS FILE. Use zonecfg(1M) instead.
-->
<zone name="myzone" zonepath="/zones/myzone" autoboot="true" brand="solaris" ip-type="exclusive">
<automatic-network lower-link="auto" linkname="net0" link-protection="mac-nospoof" mac-address="random"/>
</zone>
Display the zones on your system by using the list subcommand of the zoneadm command:
root@solaris:~# zoneadm list -cv ID NAME STATUS PATH BRAND IP 0 global running / solaris shared - myzone configured /zones/myzone solaris excl
The switches used with the list subcommand are:
| Switch | Description |
|---|---|
| -c | Display all zones |
| -v | Display verbose output |
Installing a Zone
Now you are ready to install the zone with the following command:
root@solaris:~# zoneadm -z myzone install
Go grab a cup of coffee or juice ! The installation process can take upto 20 minutes.
When installation is complete, you will see something similar to the following:
root@solaris:~# zoneadm -z myzone install
The following ZFS file system(s) have been created:
rpool/zones/myzone
Progress being logged to /var/log/zones/zoneadm.20121214T123059Z.myzone.install
Image: Preparing at /zones/myzone/root.
AI Manifest: /tmp/manifest.xml.UWaiVk
SC Profile: /usr/share/auto_install/sc_profiles/enable_sci.xml
Zonename: myzone
Installation: Starting ...
Creating IPS image
Startup linked: 1/1 done
Installing packages from:
solaris
origin: http://pkg.oracle.com/solaris/release/
DOWNLOAD PKGS FILES XFER (MB) SPEED
Completed 183/183 33556/33556 222.2/222.2 154k/s
PHASE ITEMS
Installing new actions 46825/46825
Updating package state database Done
Updating image state Done
Creating fast lookup database Done
Installation: Succeeded
Note: Man pages can be obtained by installing pkg:/system/manual
done.
Done: Installation completed in 3389.965 seconds.
Next Steps: Boot the zone, then log into the zone console (zlogin -C)
to complete the configuration process.
Log saved in non-global zone as /zones/myzone/root/var/log/zones/zoneadm.20121214T123059Z.myzone.install
Now use zonesadm's list subcommand to display the zones:
root@solaris:~# zoneadm list -cv ID NAME STATUS PATH BRAND IP 0 global running / solaris shared - myzone installed /zones/myzone solaris excl
Note that the myzone STATUS is now installed as opposed to configured.
A Zone's First Boot
Verify myzone and then boot it:
root@solaris:~# zoneadm -z myzone verify root@solaris:~# zoneadm -z myzone boot
Check if the zone status is now running:
root@solaris:~# zoneadm list -cv ID NAME STATUS PATH BRAND IP 0 global running / solaris shared 1 myzone running /zones/myzone solaris excl
Now you can login to the zone using the zlogin command:
root@solaris:~# zlogin -C myzone [Connected to zone 'myzone' console]
Hit ↵ Enter and configure the zone:
- host name = myzone.fenestros.loc
- time zone = Europe/Paris
- root password = Wind0w$
- user name and login = myzone
- user password = fenestr0$
Once configured you will see messages similar to the following:
SC profile successfully generated. Exiting System Configuration Tool. Log is available at: /system/volatile/sysconfig/sysconfig.log.7316
Use the tilde-dot ( ~. ) shortcut to leave the zone and return to your global zone:
~. [Connection to zone 'myzone' console closed] root@solaris:~#
Logging into a Zone Directly as Root
Log back into the zone as root using the -S switch of the zlogin command:
root@solaris:~# zlogin -S myzone [Connected to zone 'myzone' pts/4] @myzone:~$ whoami root @myzone:~$ ~. [Connection to zone 'myzone' pts/4 closed] root@solaris:~#
Logging into a Zone as a specific User
To log into the zone as the myzone user that you previously created, use the following command:
root@solaris:~# zlogin -l myzone myzone [Connected to zone 'myzone' pts/4] No directory! Logging in with home=/ Oracle Corporation SunOS 5.11 11.1 September 2012 -bash-4.1$ whoami myzone -bash-4.1$ ~. [Connection to zone 'myzone' pts/4 closed] root@solaris:~#
LAB #2 - Administering Zones
Sharing Files between the Global and Local Zones
To share files between the two zones, you need to configure a LOFS mount.
In the global zone, create a directory for sharing files:
root@solaris:~# mkdir -p /root/zones/myzone
Now use the zonecfg command to configure the share:
root@solaris:~# zonecfg -z myzone zonecfg:myzone> add fs zonecfg:myzone:fs> set dir=/root/share zonecfg:myzone:fs> set special=/root/zones/myzone zonecfg:myzone:fs> set type=lofs zonecfg:myzone:fs> add options [rw,nodevices] zonecfg:myzone:fs> end zonecfg:myzone> exit root@solaris:~#
Note that dir indicates the mount point in the local zone whilst special indicates the share in the global zone.
Now create a file in /root/zones/myzone:
root@solaris:~# touch /root/zones/myzone/testshare
Reboot myzone, check it is up and running, log into myzone as root and check you can see the share. Finally, create a file in /root/share:
root@solaris:~# zoneadm -z myzone reboot root@solaris:~# zoneadm list -cv ID NAME STATUS PATH BRAND IP 0 global running / solaris shared 2 myzone running /zones/myzone solaris excl root@solaris:~# zlogin -S myzone [Connected to zone 'myzone' pts/4] @myzone:~$ cd /root @myzone:~root$ ls share @myzone:~root$ ls share testshare @myzone:~root$ touch share/shareback @myzone:~root$ ls share shareback testshare
Leave myzone and check if you can see the shareback file from the global zone:
@myzone:~root$ ~. [Connection to zone 'myzone' pts/4 closed] root@solaris:~# ls /root/zones/myzone shareback testshare
You can also share the global zone's DVD-ROM drive. However do not use the process explained above since it creates a permanent LOFS mount which will stop you ejecting the DVD from the global zone's DVD-ROM drive whilst the local zone is running:
root@solaris:~# mkdir /zones/myzone/root/globaldvdrom root@solaris:~# ls /cdrom/cdrom0 32Bit autorun.sh runasroot.sh VBoxWindowsAdditions-amd64.exe 64Bit cert VBoxLinuxAdditions.run VBoxWindowsAdditions-x86.exe AUTORUN.INF OS2 VBoxSolarisAdditions.pkg VBoxWindowsAdditions.exe root@solaris:~# mount -F lofs /cdrom/cdrom0 /zones/myzone/root/globaldvdrom
Now check you can see the contents of the DVD from within the local zone:
root@solaris:~# zlogin myzone ls /globaldvdrom 32Bit 64Bit AUTORUN.INF autorun.sh cert OS2 runasroot.sh VBoxLinuxAdditions.run VBoxSolarisAdditions.pkg VBoxWindowsAdditions-amd64.exe VBoxWindowsAdditions-x86.exe VBoxWindowsAdditions.exe
Finally unmount the DVD-Rom and eject it:
root@solaris:~# umount /zones/myzone/root/globaldvdrom root@solaris:~# eject cdrom cdrom /dev/dsk/c7t1d0s2 ejected
Removing the Share
In order to remove the LOFS share, proceed as follows:
root@solaris:~# zonecfg -z myzone zonecfg:myzone> info fs fs: dir: /root/share special: /root/zones/myzone raw not specified type: lofs options: [rw,nodevices] zonecfg:myzone> remove fs dir=/root/share zonecfg:myzone> exit root@solaris:~# zoneadm -z myzone reboot
Allocating CPU Resources
First, lets see what the non-global zone currently sees as available processors:
root@solaris:~# zlogin myzone psrinfo -v Status of virtual processor 0 as of: 12/15/2012 06:54:05 on-line since 12/15/2012 07:25:33. The i386 processor operates at 2271 MHz, and has an i387 compatible floating point processor. Status of virtual processor 1 as of: 12/15/2012 06:54:05 on-line since 12/15/2012 07:25:34. The i386 processor operates at 2271 MHz, and has an i387 compatible floating point processor.
As you can see, the zone has grabbed both of the processors available in the global zone. In order to limit the availabilty to just 1 processor, you need to change the zone's configuration:
root@solaris:~# zonecfg -z myzone zonecfg:myzone> add dedicated-cpu zonecfg:myzone:dedicated-cpu> set ncpus=1 zonecfg:myzone:dedicated-cpu> end zonecfg:myzone> exit root@solaris:~# zoneadm -z myzone reboot root@solaris:~# zlogin myzone psrinfo -v Status of virtual processor 0 as of: 12/15/2012 07:12:29 on-line since 12/15/2012 07:25:33. The i386 processor operates at 2271 MHz, and has an i387 compatible floating point processor.
The dedicated cpu is now invisible to all other non-global zones. You can also define a range of CPUs, such as 1-3, in which case, when the non-global zone boots, the system will allocate 1 CPU as a minimum and 2 or 3 CPUs if they are available.
Before proceeding further, remove the dedicated CPU:
root@solaris:~# zonecfg -z myzone "remove dedicated-cpu" root@solaris:~# zoneadm -z myzone reboot
Fair Share Scheduler
Another way of sharing resources is to use the Fair Share Scheduler. Firstly, you need to set that scheduler as the default for the system:
root@solaris:~# dispadmin -d FSS root@solaris:~# dispadmin -l CONFIGURED CLASSES ================== SYS (System Class) TS (Time Sharing) SDC (System Duty-Cycle Class) FX (Fixed Priority) IA (Interactive) RT (Real Time) FSS (Fair Share)
Next set the FSS scheduler as the default for your zone:
root@solaris:~# zonecfg -z myzone "set scheduling-class=FSS"
Now you can give your global zone 75% of your processors leaving 25% for your zone:
root@solaris:~# zonecfg -z global zonecfg:global> set cpu-shares=75 zonecfg:global> exit root@solaris:~# zonecfg -z myzone zonecfg:myzone> set cpu-shares=25 zonecfg:myzone> exit
Finally use the prstat command to display the CPU resource balancing:
PID USERNAME SIZE RSS STATE PRI NICE TIME CPU PROCESS/NLWP
3725 trainee 518M 180M sleep 49 0 0:31:48 0.4% firefox/21
3738 trainee 129M 18M sleep 59 0 0:00:37 0.4% gnome-terminal/2
11208 daemon 14M 3380K sleep 59 0 0:00:04 0.3% rcapd/1
1159 trainee 169M 152M sleep 59 0 0:04:51 0.1% Xorg/3
3661 trainee 227M 149M sleep 59 0 0:03:32 0.1% java/23
5 root 0K 0K sleep 99 -20 0:01:11 0.1% zpool-rpool/136
3683 trainee 13M 724K sleep 59 0 0:01:25 0.0% VBoxClient/3
12971 root 11M 3744K cpu1 59 0 0:00:00 0.0% prstat/1
12134 netadm 5340K 2808K sleep 59 0 0:00:00 0.0% nwamd/7
12308 root 5880K 2296K sleep 59 0 0:00:00 0.0% nscd/25
3645 trainee 150M 35M sleep 59 0 0:00:06 0.0% gnome-panel/2
3644 trainee 128M 15M sleep 59 0 0:00:12 0.0% metacity/1
12400 root 3964K 1008K sleep 59 0 0:00:00 0.0% syslogd/11
3658 trainee 61M 23M sleep 12 19 0:00:03 0.0% updatemanagerno/1
814 root 16M 6288K sleep 59 0 0:00:05 0.0% nscd/37
932 root 11M 600K sleep 59 0 0:00:05 0.0% VBoxService/7
957 root 11M 1144K sleep 59 0 0:00:00 0.0% syslogd/11
818 root 0K 0K sleep 99 -20 0:00:00 0.0% zpool-mypool/136
637 root 9408K 1036K sleep 59 0 0:00:00 0.0% dhcpagent/1
881 daemon 3356K 4K sleep 59 0 0:00:00 0.0% rpcbind/1
95 netadm 4296K 680K sleep 59 0 0:00:00 0.0% ipmgmtd/6
104 root 9692K 388K sleep 59 0 0:00:00 0.0% in.mpathd/1
85 daemon 16M 2940K sleep 59 0 0:00:00 0.0% kcfd/3
50 root 16M 1560K sleep 59 0 0:00:00 0.0% dlmgmtd/7
ZONEID NPROC SWAP RSS MEMORY TIME CPU ZONE
0 124 4095M 973M 48% 0:53:57 1.4% global
3 28 137M 46M 2.2% 0:00:08 0.0% myzone
Total: 152 processes, 956 lwps, load averages: 0.08, 0.12, 0.12
Allocating Memory
Three types of memory capping are possible within a zone:
| Cap | Description |
|---|---|
| Physical | Total amount of physical memory available to the zone. Once past the cap, memory pages are paged out |
| Locked | Amount of memory that can be allocated to a greedy application by a zone |
| Swap | Amount of swap space that can be used by a zone |
To cap the physical memory of a zone, you need to add and correctly configure the capped-memory property:
root@solaris:~# zonecfg -z myzone zonecfg:myzone> add capped-memory zonecfg:myzone:capped-memory> set physical=50m zonecfg:myzone:capped-memory> end zonecfg:myzone> exit root@solaris:~# zonecfg -z myzone info capped-memory capped-memory: physical: 50M
Zone Statistics
Zone statistics can be displayed by using the zonestat command:
root@solaris:~# zonestat 5 3
Collecting data for first interval...
Interval: 1, Duration: 0:00:05
SUMMARY Cpus/Online: 2/2 PhysMem: 2047M VirtMem: 3071M
---CPU---- --PhysMem-- --VirtMem-- --PhysNet--
ZONE USED %PART USED %USED USED %USED PBYTE %PUSE
[total] 0.23 11.9% 1495M 73.0% 1967M 64.0% 0 0.00%
[system] 0.19 9.68% 309M 15.1% 891M 29.0% - -
global 0.04 4.52% 1134M 55.4% 1024M 33.3% 0 0.00%
myzone 0.00 0.10% 51.3M 2.50% 51.5M 1.67% 0 0.00%
Interval: 2, Duration: 0:00:10
SUMMARY Cpus/Online: 2/2 PhysMem: 2047M VirtMem: 3071M
---CPU---- --PhysMem-- --VirtMem-- --PhysNet--
ZONE USED %PART USED %USED USED %USED PBYTE %PUSE
[total] 0.06 3.47% 1495M 73.0% 1967M 64.0% 0 0.00%
[system] 0.02 1.00% 310M 15.1% 891M 29.0% - -
global 0.04 4.80% 1134M 55.4% 1024M 33.3% 0 0.00%
myzone 0.00 0.14% 51.3M 2.50% 51.5M 1.67% 0 0.00%
Interval: 3, Duration: 0:00:15
SUMMARY Cpus/Online: 2/2 PhysMem: 2047M VirtMem: 3071M
---CPU---- --PhysMem-- --VirtMem-- --PhysNet--
ZONE USED %PART USED %USED USED %USED PBYTE %PUSE
[total] 0.07 3.83% 1494M 72.9% 1963M 63.9% 0 0.00%
[system] 0.02 1.10% 308M 15.0% 891M 29.0% - -
global 0.05 5.34% 1134M 55.4% 1020M 33.2% 0 0.00%
myzone 0.00 0.12% 51.3M 2.50% 51.5M 1.67% 0 0.00%
Non-global Zone Privileges
Certain things cannot be done from within a non-global zone. The list of privileges assigned to a zone can be displayed as follows:
root@solaris:~# zlogin myzone ppriv -l contract_event contract_identity contract_observer cpc_cpu dtrace_kernel dtrace_proc dtrace_user file_chown file_chown_self file_dac_execute file_dac_read file_dac_search file_dac_write file_downgrade_sl file_flag_set file_link_any file_owner file_read file_setid file_upgrade_sl file_write graphics_access graphics_map ipc_dac_read ipc_dac_write ipc_owner net_access net_bindmlp net_icmpaccess net_mac_aware net_mac_implicit net_observability net_privaddr net_rawaccess proc_audit proc_chroot proc_clock_highres proc_exec proc_fork proc_info proc_lock_memory proc_owner proc_priocntl proc_session proc_setid proc_taskid proc_zone sys_acct sys_admin sys_audit sys_config sys_devices sys_ipc_config sys_linkdir sys_mount sys_iptun_config sys_flow_config sys_dl_config sys_ip_config sys_net_config sys_nfs sys_ppp_config sys_res_bind sys_res_config sys_resource sys_share sys_smb sys_suser_compat sys_time sys_trans_label win_colormap win_config win_dac_read win_dac_write win_devices win_dga win_downgrade_sl win_fontpath win_mac_read win_mac_write win_selection win_upgrade_sl
Changing a Zone's Name
To change the name of a zone, it first has to be shutdown:
root@solaris:~# zoneadm -z myzone halt
Now you can change the zone name:
root@solaris:~# zonecfg -z myzone "set zonename=myzone1" root@solaris:~# zoneadm list -cv ID NAME STATUS PATH BRAND IP 0 global running / solaris shared - myzone1 installed /zones/myzone solaris excl
Changing a Zone's Root Dataset
To change the underlying root dataset of your myzone1 zone use the following command:
root@solaris:~# zoneadm -z myzone1 move /zones/myzone1 root@solaris:~# zoneadm list -cv ID NAME STATUS PATH BRAND IP 0 global running / solaris shared - myzone1 installed /zones/myzone1 solaris excl
Backing Up a Zone
Backing up a zone includes backing up the zone configuration and the application data in it. You can use any kind of backup software to backup data within the zone and then export it such that it may be re-injected after a zone restore. The zone configuration is backed up as follows:
root@solaris:~# zonecfg -z myzone1 export -f myzone1.config root@solaris:~# cat myzone1.config create -b set brand=solaris set zonepath=/zones/myzone1 set autoboot=true set scheduling-class=FSS set ip-type=exclusive add anet set linkname=net0 set lower-link=auto set configure-allowed-address=true set link-protection=mac-nospoof set mac-address=random end add capped-memory set physical=50M end add rctl set name=zone.cpu-shares add value (priv=privileged,limit=25,action=none) end
Now backup the zone's xml file:
root@solaris:~# cp /zones/myzone1/root/etc/svc/profile/site/scit_profile.xml /root/myzone1.xml
Restoring a Zone
Disaster has struck! Uninstall and delete myzone1:
root@solaris:~# zoneadm -z myzone1 uninstall Are you sure you want to uninstall zone myzone1 (y/[n])? y Progress being logged to /var/log/zones/zoneadm.20121218T170820Z.myzone1.uninstall root@solaris:~# root@solaris:~# zonecfg -z myzone1 delete Are you sure you want to delete zone myzone1 (y/[n])? y
Now restore myzone1 as follows:
root@solaris:~# zonecfg -z myzone1 -f myzone1.config
root@solaris:~# zoneadm -z myzone1 install -c /root/myzone1.xml
The following ZFS file system(s) have been created:
rpool/zones/myzone1
Progress being logged to /var/log/zones/zoneadm.20121218T171621Z.myzone1.install
Image: Preparing at /zones/myzone1/root.
AI Manifest: /tmp/manifest.xml.9BaOQP
SC Profile: /root/myzone1.xml
Zonename: myzone1
Installation: Starting ...
Creating IPS image
Startup linked: 1/1 done
Installing packages from:
solaris
origin: http://pkg.oracle.com/solaris/release/
DOWNLOAD PKGS FILES XFER (MB) SPEED
Completed 183/183 33556/33556 222.2/222.2 674k/s
PHASE ITEMS
Installing new actions 46825/46825
Updating package state database Done
Updating image state Done
Creating fast lookup database Done
Installation: Succeeded
Note: Man pages can be obtained by installing pkg:/system/manual
done.
Done: Installation completed in 678.453 seconds.
Next Steps: Boot the zone, then log into the zone console (zlogin -C)
to complete the configuration process.
Log saved in non-global zone as /zones/myzone1/root/var/log/zones/zoneadm.20121218T171621Z.myzone1.install
Log in as root and check the zone is running correctly:
root@solaris:~# zlogin -S myzone1 [Connected to zone 'myzone1' pts/3] @myzone.solaris.loc:~$ ls bin dev etc export home lib mnt net nfs4 opt proc root rpool sbin system tmp usr var
Cloning a Local Zone
In this section you are going to create a template zone that you can clone as necessary every time you need to install a new zone. Start by creating a zone called cleanzone:
root@solaris:~# zonecfg -z cleanzone Use 'create' to begin configuring a new zone. zonecfg:cleanzone> create create: Using system default template 'SYSdefault' zonecfg:cleanzone> set zonepath=/zones/cleanzone zonecfg:cleanzone> set autoboot=true zonecfg:cleanzone> verify zonecfg:cleanzone> commit zonecfg:cleanzone> exit
Install the zone:
root@solaris:~# zoneadm -z cleanzone install
The following ZFS file system(s) have been created:
rpool/zones/cleanzone
Progress being logged to /var/log/zones/zoneadm.20121218T143129Z.cleanzone.install
Image: Preparing at /zones/cleanzone/root.
AI Manifest: /tmp/manifest.xml.vAaqcB
SC Profile: /usr/share/auto_install/sc_profiles/enable_sci.xml
Zonename: cleanzone
Installation: Starting ...
Creating IPS image
Startup linked: 1/1 done
Installing packages from:
solaris
origin: http://pkg.oracle.com/solaris/release/
DOWNLOAD PKGS FILES XFER (MB) SPEED
Completed 183/183 33556/33556 222.2/222.2 552k/s
PHASE ITEMS
Installing new actions 46825/46825
Updating package state database Done
Updating image state Done
Creating fast lookup database Done
Installation: Succeeded
Note: Man pages can be obtained by installing pkg:/system/manual
done.
Done: Installation completed in 797.979 seconds.
Next Steps: Boot the zone, then log into the zone console (zlogin -C)
to complete the configuration process.
Log saved in non-global zone as /zones/cleanzone/root/var/log/zones/zoneadm.20121218T143129Z.cleanzone.install
Boot the zone to import the zone's manifest:
root@solaris:~# zoneadm -z cleanzone boot
Login to the zone and hit ↵ Enter then immediately leave the zone by using the ~. shortcut:
root@solaris:~# zlogin -C cleanzone
To clone a zone, it first needs to be shutdown:
root@solaris:~# zoneadm -z cleanzone halt root@solaris:~# zoneadm list -cv ID NAME STATUS PATH BRAND IP 0 global running / solaris shared 3 myzone1 running /zones/myzone1 solaris excl - cleanzone installed /zones/cleanzone solaris excl
Now create a clone of cleanzone:
root@solaris:~# zonecfg -z myzone2 "create -t cleanzone"
root@solaris:~# zonecfg -z myzone2 "set zonepath=/zones/myzone2"
root@solaris:~# zoneadm -z myzone2 clone cleanzone
The following ZFS file system(s) have been created:
rpool/zones/myzone2
Progress being logged to /var/log/zones/zoneadm.20121218T174936Z.myzone2.clone
Log saved in non-global zone as /zones/myzone2/root/var/log/zones/zoneadm.20121218T174936Z.myzone2.clone
References
<html>
Copyright © 2011-2015 Hugh Norris.<br><br> <a rel=“license” href=“http://creativecommons.org/licenses/by-nc-nd/3.0/”><img alt=“Creative Commons License” style=“border-width:0” src=“http://i.creativecommons.org/l/by-nc-nd/3.0/88x31.png” /></a><br />This work is licensed under a <a rel=“license” href=“http://creativecommons.org/licenses/by-nc-nd/3.0/”>Creative Commons Attribution-NonCommercial-NoDerivs 3.0 Unported License</a>.
</html>
